Motor Factory Rocker Arm Shims, +.005"

9.79 for more details check www.custom-chrome-europe.com ENGINE APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS JIMS Roller Rockers for Shovelhead Models Designed to reduce friction in the valve train. This provides more horsepower and less heat in the top end. Fits Shovelhead models from 66-84 (1.43:1 stock ratio). 20922 Sold in sets of four Replacement Parts 20973 Rocker arm rollers (pack of 4) 20960 Rocker arm axles (pack of 4) 20961 Rocker arm lock rings (pack of 8) Rocker Arms for Sportster Models Fit Sportster models from 57-85. Sold each. 28029 Front exhaust (repl. OEM 17394-57A) 28030 Rear exhaust (repl. OEM 17395-57A) 28031 Front intake (repl. OEM 17396-57A) 28032 Rear intake (repl. OEM 17397-57A) Rockershaft and Bushings for Evolution and Twin Cam Models American-made, precision-ground and hard- ened steel shaft that duplicates the Original Equipment part. Fits all Evolution and Twin Cam motors from 84-Up. Replacement bushing fits all Big Twin models 66-Up and Sportster models 57-Up. 28027 Rocker arm shaft. Fits 84-17 Big Twin and 86-19 Sportster 95-02 Buell models (repl. OEM 17611-83) (sold each) JIMS Rockershafts Precision-ground high-quality rocker shafts replace Original Equipment parts perfectly. Precision shafts are American-made and cen- terless ground for accuracy. Stock diameter. Sold each. 20639 Fits 86-19 Sportster and L84-17 Big Twin engines, and 99-17 Twin Cam 95-02 Buell engines (repl. OEM 17611- 83) 20638 Fits Shovelhead Big Twin engines from 66-84 (repl. OEM 17611-66B) 20639 20083 26078 Rockershafts Replacement rockershafts for Big Twin and Sportster models. Sold each. 26078 Fits Shovelhead Big Twins 71-84 (repl. OEM 17611-66B) 20083 Rockerarm shims for Shovelheads 66-84 (.007") pack of 10 628000 Rockerarm spacer for Shovelheads (repl. OEM 17452-66) Kibblewhite Bronze Alloy Rocker Arm Bushings Made from solid U.S. Mill certified SAE 660 bearing bronze bar stock. This high performance bronze mate- rial is an excellent choice for performance applications because it is highly resistant to impact, wear, and corrosion, and has superb anti-friction properties. It also has excellent machinability, meaning a high quality surface finish can be achieved. This combination of mechanical properties cre- ates a tough durable bushing that can give excellent performance even under the high spring pressures and impact loads common in these engines. Sold as a set of 8. Sold as a set of 8. 55138 Fit all Big Twin models from 66-17(except 17 Touring) and Sportster models 57-19 (repl. OEM# 17428-57 & 17429-91) Note: Must be installed and sized according to factory service manual. JIMS Rocker Arm Bushings Replacement bushings made from solid bronze bar stock. Sets of 8. 20637 Fit all Big Twins from 66-84 and all Sportster models from 57-85 (repl. OEM 17428-57) 20958 Fit all L84-17 Twin Cam and Evolution Big Twin and 86-19 Sportster models and Buell models from 86-02 (repl. OEM 17428-83) Note: CC #20958 is same as #20637 but without the mill slot. Do not use CC #20958 on Shovelheads or Ironhead Sportster models. 20637 Rocker Arm Shim Kit for Shovelhead Engines Reduces top end noise with special pre-loaded spring shims installed on the pushrod side of the rocker shaft. Includes spring shims, spacers, and rocker plug seals. The seals are designed to conform to the rocker shaft and cover hole for a positive seal. Seals are also available sepa- rately. Fits Shovelhead models 66-84. 010519 Rocker arm shim and seal kit 010518 Rocker arm (special seals designed to conform to the rocker shaft and cover hole), 46-E84 (pack of 4) Motor Factory Rocker Arm Shims Fit all Shovelhead engines from 66-84. Sold in packs of 10. 010501 .005"-thick 010537 .010"-thick 010515 .015"-thick 010538 .020"-thick 010501 Panhead Rocker Oilers and Nuts Exact reproductions of Original Equipment intake rocker oilers and the self-locking rocker arm stud nuts. 26077 Rocker arm oilers (repl. OEMs 18100-49 and 18102-49) sold in pairs 26083 Rocker arm stud nuts (repl. OEM 7727) pack of 25 26083 26077 Panhead Rocker Arms and Assemblies Quality reproductions of the stock parts for 48-65 Panheads. Rocker Arms Only, Sold each. 26074 Fits rear exhaust/front intake (repl. OEM 17360-48) 26075 Fits front exhaust/rear intake (repl. OEM 17375-48) Complete Assemblies, Sold each. 26081 Fits rear exhaust/front intake 26082 Fits front exhaust/rear intake 26075 26081 26082 26074 20638