19 19.30 EDITION 50 619286 619285 Fork Oil Level Tool • Use this tool to check and adjust the oil level on conventional and single chamber cartridge forks • Adjustable ring will measure oil levels from 0 to 300 mm in 5 mm increments • Syringe has a capacity of 60 ml • New plunger head design features two fluorocarbon elastomer X-Ring seals that provide superior sealing and chemical resistance • Billet aluminum plunger knob with durable black anodized finish • New plunger head design allows easy cleaning and replacement of seals Part#: 922058 , Unit: Set , Qty.: 1 Ballancer Bearing Installer for Milwaukee Eight All Milwaukee-Eight engines (Softail and Touring)incorporate balancers to reduce vibration. JIMS has now developed a balancer bearing installer, which can be used in conjunction with the existing JIMS balancer bearing remover, to precisely install these bearings in the proper location for all Milwaukee-Eight engines. Incorrect installation of these bearings can cause severe damage to the crankcase,or even complete engine failure. This precision machined installer, aligns to the crankcase via case bolt and dowel locations, allowing the technician to install the bearings on a workbench without the use of a driver or press. Ballancer Bearing Remover for Milwaukee Eight The Milwaukee-Eight engine design incorporates balancers to reduce engine vibration. This tool can remove the balancer bearings in both Touring and Softail models without damage to the crankcase. Wrist Pin Remover Adapter JIMS No. 5805 Wrist Pin Remover Adapter is designed to be used with JIMS No. 1276 Wrist Pin Remover Tool on 2017-present Milwaukee 8 four valve engines. Part#: 900902 , Fitment: 18-24 Softail, 17-24 Touring, 17-24 Trike , Unit: Each , Qty.: 1 Mighty Bite Crankshaft Locking Tool for Milwaukee Eight • For Twin Cam models designed to lock the crankshaft when doing service work • The new Milwaukee Eight™ has a different crank position sensor location and requires a different profile to lock the flywheel • This tool specifically locates and locks the flywheel in the new Milwaukee Eight engine and has an added o-ring to prevent oil leakag Part#: 900916 , Fitment: 18-24 Softail, 17-24 Touring, 17-24 Trike , Unit: Each , Qty.: 1 Fork Cap Allen Socket Part#: 900918 , Fitment: 14-24 Touring, 14-24 Trike , Unit: Each , Qty.: 1 Swing Arm Bearing Installer Swingarm Bearing Installer is designed for use on 2002-present FLH Touring. Part#: 900915 , Fitment: 02-24 Touring, 09-24 Trike , Unit: Set , Qty.: 1 Head Holder for Milwaukee Eight Cylinder Head Holding Tool for use on Milwaukee Eight four valve heads and Twin Cam cylinder heads. Part#: 900919 , Fitment: 00-24 Softail, 99-24 Touring, 99-17 Dyna, 09-24 Trike , Unit: Set , Qty.: 1 Sensor Wrench JIMS has just released two new 2012 oxygen sensor wrenches. A must have to remove or install the O2 sensors without removing the exhaust pipes on the motorcycle. Unit: Each , Qty.: 1 PART# FITMENT FITMENT NOTE 619285 12-17 Dyna, 12-24 Softail, 12-17 V-Rod Softail models only front O2 sensor 619286 12-24 Softail Only rear O2 sensor Fork Stem Nut Wrench Normally to get access to the top stem nut you would need to remove theradio package. With this tool you’re able to loosen, tightenand torque to spec. the 1-1/2” stem nut without radioremoval and ultimatelysaving 45 minutes for an experienced Harley mechanic. Part#: 619287 , Fitment: 96-13 Touring, 94-95 FLHR, (except 96 FLTCUI, 99-03, 07-09 FLTR, 99-06 FLTRI, 09 FLTRSE3, 10, 13 FLTRX, 11 FLTRUSE, 12 FLTRXSE, 13 FLTRU, 13 FLTRXSE2, 13 FLTRXSE2 ANV) , Unit: Each , Qty.: 1 Part#: 917610 , Fitment: 17-24 Touring, 18-24 Softail, 17-24 Trike , Unit: Each , Qty.: 1 Part#: 917609 , Fitment: 17-24 Touring, 18-24 Softail, 17-24 Trike , Unit: Each , Qty.: 1
RkJQdWJsaXNoZXIy ODQ0NDEw