APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS 19.35 FOR MORE DETAILS CHECK WWW.CUSTOM-CHROME-EUROPE.COM 20629 Motion Pro Degree Wheel Aluminum construction with a 6 3⁄4" outside diameter and a 6 mm center hole. Can be used on all motorcycles to check or set up ignition timing. May also be used on 4-stroke engines to check or alter cam timing. Sold each. 5008092 Motion Pro Degree Wheel Piston Support Plate Using this tool will give you peace of mind when installing your rings and cylinders by providing a non-marring flat support to push the bottom of the piston agents as you install the rings and cylinder over the piston. Part#: 671018 , Field of Application: For all HD Models , Unit: Each , Qty.: 1 Inner Cam Bearing Puller Designed like the version for Evolution models, it removes the bearing easily without any damage to the crankcase. This precision-built tool will also keep the pin rollers from accidentally falling into the crankcase. Part#: 20292 , Fitment: 99-05 Dyna, 00-06 Softail, 99-06 Touring , Position: Inner , Unit: Each , Qty.: 1 Cam Bearing Puller Tool Once the cams are removed from the support plate, this tool will remove the bearing. Unlike a general purpose puller this tool was designed to remove the bearing straight with no slipping or binding. Part#: 20296 , Fitment: 99-05 Dyna, 00-06 Softail, 99-06 Touring , Position: Outer , Unit: Each , Qty.: 1 Cam Bushing Reamer Tool Line reams cam cover bushings from inner cam bearing for a true centerline between the two dimensions. Part#: 20629 , Fitment: 70-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Each , Qty.: 1 Cam Bearing Puller Tool Easily pulls the inner cam bearing without splitting the cases. It also keeps the rollers from coming out during removal. Part#: 20695 , Fitment: 58-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 86-98 Touring , Unit: Each , Qty.: 1 Cam Bearing Tool Used to install inner cam bearing. Fits single cam Big Twins from 58-99. Sold each. Part#: 20699 , Fitment: 58-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 86-98 Touring , OEM #: 9727260 , Unit: Each , Qty.: 1 Big Twin Cam Seal Remover + Installer Install or remove cam seal without removing the cam cover. Easy-to-use tool pulls the seal and drives in a new one flat and square for a no-leak repair. The tool can also be used to remove the cam cover from the case. Part#: 20762 , Fitment: 70-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Each , Qty.: 1 Inner Cam Bearing Installation Tool Smoothly presses the inner cam bearing to the right depth into the right-side case when both case halves are assembled. Part#: 20774 , Fitment: 58-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 86-98 Touring , Unit: Each , Qty.: 1 Cam Gear Alignment Tool This precision tool will remove the cam gear on any single cam Big Twin from 7099, and reposition it on another cam shaft in exactly the same spot. Pressing the gear on in the advanced or retarded position is also possible. Save time and ensure accuracy time after time. Part#: 400340 , Fitment: 70-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Each , Qty.: 1
RkJQdWJsaXNoZXIy ODQ0NDEw