19 19.42 EDITION 50 Motion Pro Tappet Tool Removes and fastens the tappet oil filter screen cover without removing exhaust on some models, and avoid scratching your engine cases. Sold each. • Includes O-ring to retain it in a 7/16" wrench or socket drive • Hex 7/16" drive allows more rotation before contacting cases • Flange design allows downward force to be applied to tool • The tappet oil filter screen is required to be serviced at every oil change • Fits all Big Twins (except Twin Cam 88) with slotted screw tappet oil filter screen cover 640110 Tappet Tool Rod Lapping Tool Fits Big Twins, Sportster and K models, 45“ and Indian rods (except Twin Cam 88 models). Includes arbor assembly, 1.500“ lap for 45“, Indian and some case races. 1.625“ lap for Big Twin, Sportster and K model rods. Part#: 26409 , Fitment: 52-53 Sportster, 29-52 Flathead, 36-47 Knucklehead, 48-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Kit , Qty.: 1 Tappet Guide Puller Tappet guide puller tool which slides into the matching grooves of the tappe guide. When the tool is centered tighten the screw until the guide is clear of the engine case. Part#: 20104 , Fitment: 57-78 Sportster , OEM #: 95724-57 , Unit: Each , Qty.: 1 Sprocket Shaft Bearing Tool For installing the crankshaft into the crankcase Timken bearing. - Used with CC #20116 to press oil seal over sprocket shaft into the case. Part#: 20116 , Fitment: 69-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-05 Dyna, 84-06 Softail, 8606 Touring , Unit: Each , Qty.: 1 Pinion Bushing Installer + Drilling Jig These drill jigs ensure exact factory bushing dowel pin location when building performance engines. Supplied with jig and drill bit. Part#: 20623 , Fitment: 54-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-92 FX Model, 91-92 Dyna, 84-92 Softail, 86-92 Touring , Unit: Each , Qty.: 1 Sprocket Flywheel Rebuilding Socket - Sprocket Shaft Nut Socket Low profile, yet provide 100% nut coverage. The socket end is machined flat to eliminate rounding-off the flywheel nut. Made from 4130 chrome-moly and heat-treated for strength. Part#: 20634 , Fitment: 72-84 FL Shovel, 72-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Each , Qty.: 1 Race and Bearing Installing Tool Handle Race and bearing installing tool handle to be used with JIMS tool No’s. 3307173, 2232, 34810-84, 788, 94547-80A&B, 97272-60 and 97273-60. Use a press fit lube. If a press is not available, it is highly recommended that you use a JIMS No.1080 brass hammer. Part#: 20666 , Field of Application: For Cam Bearing Driver 20699 , Unit: Each , Qty.: 1 Wheel Bearing Race Remover + Installer Use with bearing driver tools to apply outward pressure to grip the race for easier installation and removal. Part#: 20727 , Fitment: 73-99 Sportster, 73-84 FL Shovel, 73-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 86-98 Touring, 97-99 M2, 97-98 S1, 97-99 S3, 99 X1 , Unit: Each , Qty.: 1 Sprocket Shaft Bearing RaceTool • Used to remove and install Timken bearing race on motor cases • Use drivers with handle Unit: Each , Qty.: 1 PART# FITMENT DESCRIPTION 20688 69-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-02 Dyna, 8402 Softail, 86-02 Touring 20689 77-03 Sportster, 97-02 M2, 97-98 S1, 97-99 S3, 9902 X1 For 77-03 Sportster, 8703 Buell Timken Bearing Snap Ring Installer + Remover Removes and installs the Timken bearing outer race snap ring. A must for replacing rings in cases without inserts. No more gouging the aluminum surrounding the snap ring. Part#: 20943 , Fitment: 69-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-02 Dyna, 84-02 Softail, 8602 Touring , Unit: Each , Qty.: 1
RkJQdWJsaXNoZXIy ODQ0NDEw