APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS 19.45 FOR MORE DETAILS CHECK WWW.CUSTOM-CHROME-EUROPE.COM Primary Drive Lock Tool 894889 With step fits all models Flywheel Runout (Trueness) Inspection Gauge Check flywheel runout of the pinion shaft while assembled in engine case. Also check the amount of gear lash on gear driven cams used in some twin cam engines. By using a JIMS tire rotator No. 936 you can remove most all of the stress being applied to the flywheel by not rotating the engine with the electric starter motor. Part#: 622183 , Fitment: 70-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-17 Dyna, 84-17 Softail, 8616 Touring, 09-16 Trike , Unit: Each , Qty.: 1 Primary Chain Locking Bar Use to lock the clutch hub sprocket to the front engine sprocket. With the two sprockets locked together, engine and clutch nuts can easily be removed and retorqued. Part#: 622035 , Fitment: 06-17 Dyna, 07-24 Softail , Unit: Each , Qty.: 1 6-speed Transmission Door Remover Tool Use this tool to remove (pull) the complete door with gears and shafts from the transmission. Just prepare the trans for disassembly, bolt this tool to the outside of door, and place the two supplied press pins into the two screw holes of trans case. Thread in two of the screws, securing the door to cases, and the door is pulled from case. Part#: 622036 , Fitment: 06-17 Dyna, 07-24 Softail, 07-24 Touring, 09-24 Trike , Unit: Each , Qty.: 1 Transmission Main Drive Gear Wrench Tool Use to remove the large 2 1/4“ hex nut from the end of main drive gear, which secures the rear drive trans pulley. Just thread the inner support collar to end of mainshaft, place the socket over the collar with a 1/2“ drive tool, and unthread (right hand thread) the locknut. Part#: 622037 , Fitment: 06-17 Dyna, 07-24 Softail, 07-24 Touring, 09-24 Trike , Unit: Each , Qty.: 1 6-speed Main Drive Gear Bearing and Seal Installer Use this tool to safely install new main drive gear bearings and seal, with use of a small 1-ton press. This tool will hold bearings and seal square to its bore, eliminating any marring of the bearings and seals and installing both to the right depth. Part#: 622042 , Fitment: 06-17 Dyna, 07-24 Softail, 07-24 Touring, 09-24 Trike , Unit: Each , Qty.: 1 Main Drive Gear Seal Installer This tool is designed to properly align and install, to the right depth, the main drive gear seal H-D No.12077 into the end of the gear. This can be performed while the assembled transmission is either on a bench or in the motorcycle chassis. Part#: 622062 , Fitment: 06-17 Dyna, 07-24 Softail, 07-24 Touring, 09-24 Trike , Unit: Each , Qty.: 1 Main Case Seal Installer for Cruise Drive H-D’s new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made. These main case bearings are of such high precision that you must be very gentle when working in or around them. For this reason, JIMS has developed a driver style seal installer (not a pushing or pulling type, which could damage these bearings). This new tool installs the main seal to the correct depth, without applying any stress to the new precision bearings, or new seals. Part#: 622190 , Fitment: 06-17 Dyna, 07-24 Softail, 07-24 Touring, 09-24 Trike, 06-20 Sportster, 06-10 XB , Unit: Each , Qty.: 1 Primary Drive Locking Bar Unit: Each , Qty.: 1 PART# FITMENT FITMENT NOTE 20824 36-47 Knucklehead, 4865 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 84-06 Softail, 91-05 Dyna For 36-86 Big Twin, 85-99 Softail 20825 85-94 FX Model, 86-06 Touring Only 5-speed Models 20826 91-20 Sportster, 97-02 M2, 97-98 S1, 97-99 S3, 99-02 X1, 03-10 XB For 91-19 Sportster, 9102 Buell Gasket Locator Tool This tool will assist you in aligning the gaskets to avoid misalignment and oil leaks. Primary cover, cam cover, and transmission end cover gaskets are just a few of the possible applications. Install the locator tools into the gasket surfaces 1/4”-20 threaded holes, slip on the gasket and the cover over the pins. Next, install a few cover mounting screws and snug down. Recover the tools and finish off with the remaining screws. 3 piece set. Part#: 640094 , Field of Application: For all HD Models with 1/4“-20 threads , Unit: Each , Qty.: 1
RkJQdWJsaXNoZXIy ODQ0NDEw