3" Oil filter socket wrench with cut out for Crank Position Sensor, Genuine Zodiac
Catalog Text: This 3" oil filter socket wrench works to install and remove most OEM and aftermarket 3" oil filter cartridges as well as our Spin-On replacement oil filter & oil cooler combinations. Not suitable for S&S oil filters.
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 23-046 JIMS COMPENSATOR BOLT TORX SOCKET FOR TOURING Since 2014, all Twin Cammodels have had a change to the compensating sprocket retaining fastener to an internal drive, very large Torx-type bolt. The socket for this bolt can be difficult to find and is usually not included with tool boxes. Often it can only be purchased in an expensive set, hence we now offer it as a affordable, individually sold tool. Fits 2014 thru 2017 Twin Cam & 2017 to present Milwaukee Eight. 753650 Compensator bolt Torx socket JIMS PRIMARY LOCKING BAR FOR SPORTSTER This tool locks the primary drive on Sportster models to facilitate crankshaft sprocket nut removal and installation, along with clutch servicing. By shifting the transmission into top gear (direct drive) allows for removal, installation and accurate torque when tightening the final drive front sprocket nut. Fits all 2004 to present XL1200 and HD International Export (HDI) XL 883 models. 753641 Primary locking bar JIMS PRIMARY CHAIN LOCKING TOOL Use to lock the clutch hub sprocket to the front engine sprocket to make it easier to remove, install or re-torque engine and clutch nuts on 2006 thru 2017 Dyna and 2007 thru 2017 Softail. 750700 Primary chain locking tool JIMS PRIMARY DRIVE LOCKING TOOL Tool made by Jims from non-marring Delrin to lock front primary chain and motor sprocket. Can be used on all primaries, except 2006 and later Dyna models, 2007 and later FLH/FLT series models and 2007 and later Softail models. 750331 Primary Drive Locking Tool ZODIACS PRIMARY DRIVE LOCKING TOOL Tool locks front primary chain and motor sprocket for all 45CI, Sportster, Flathead, Knucklehead, Panhead, Shovelhead, Evolution Big Twin and Twin Cam, except 2006 and later Dyna, 2007 and later Touring and 2007 and later Softail. 210077 Primary Drive Locking Tool JIMS OIL FILTER CUTTING STAND This stand makes the task of cutting open your oil filter easy. Prevents the slippery filter drop out of your hands while trying to cut it open. The stand can be mounted to a bench or used in a vice. The u-bolt quickly tightens the filter in place with the wing nuts provided. This tool should be used in combination with oil filter cutter ZPN751080. Fits all common OEM and aftermarket spin-on filters. 751079 Oil filter cutting stand JIMS OIL FILTER CUTTER Troubleshooting the oil management system requires looking into the oil filter. Use this tool to inspect for any damaging particles that may be trapped in the filter. This tool locks down the filter for a clean cut around the filter base by rotating the filter. Use this tool in combination with the oil filter cutting stand ZPN751079. Will fit oil filters up to 5 1/2" diameter. 751080 Oil filter cutter SLIM JIMS OIL FILTER WRENCH The new Slim-JIMS Oil Filter Wrench is the slimmest on the market. Its exclusive design makes it much easier to navigate near the oil cooler and the crank position sensor, and allows for more room to work around the exhaust pipes, frame, hoses and brackets. It incorporates a 3/8" square drive and guarantees a good grip on spin-on oil filters with a 14-flute end. The Slim-JIMS Oil Filter Wrench is manufactured in the USA. Not suitable for S&S oil filters. 751109 Jims Slim Jims oil filter wrench OIL FILTER SOCKET WRENCH FOR S&S OIL FILTERS This oil filter socket wrenchworks to install and remove S&S oil filter cartridges. Not suitable for OEM, Zodiac and most other aftermarket oil filters. 743190 Oil filter socket wrench, made by Midlock OIL FILTER SOCKET WRENCH This 3" oil filter socket wrench works to install and remove most OEM and aftermarket 3" oil filter cartridges as well as our Spin-On replacement oil filter & oil cooler combinations. Not suitable for S&S oil filters. 743140 3" Oil filter socket wrench, made by Midlock 120106 3" Oil filter socket wrench with cut out for Crank Position Sensor, Genuine Zodiac JIMS ENGINE DIPSTICK SOCKET Tired of burning his hand while checking the oil level on Touring and Dyna models, Gary Smith developed this engine dipstick socket for Jims. This ingenious and patented tool allows both riders and mechanics to remove the engine oil level dipstick quickly and safely. This tool not only protects your hands from the heat, but aids riders with limited hand strength in easily checking their oil level. Features include a square hole for 3/8" ratchet fitment, 7/8" hex for wrench fitment, and a cutout for clearance around the exhaust pipe. Made of heat resistant and non-marring Delrin, ensuring strength and durability. Designed for use with the stock dipstick, not guaranteed to work with aftermarket dipsticks. 751127 Dipstick socket tool for 2007 thru 2016 Touring and 2006 thru 2017 Dyna JIMS OIL PUMP SNAP RING INSTALLER This tool will help you to easily install the outer snap ring on all Big Twin oil pump shafts, without "over-stretching" the ring. Just apply oil to the ring expander, hold up to the end of the shaft, then push ring onto the shaft with sleeve. 236219 Oil pump snap ring installer O�L� C�E�I�A�S & T�O�S OIL PUMP & OIL FILTER TOOLS ( Site 1396 )