APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS 19.37 FOR MORE DETAILS CHECK WWW.CUSTOM-CHROME-EUROPE.COM Mini-Valve Spring Tester 0 to 1000 P.S.I. Gauge Use this tool in either a bench vice, arbor, hydraulic screw press or a drill press. Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter. Precision gauge comes with a protective rubber boot. 890572 Mini-valve spring testerC Interconnect Seal Leak Testing Tool • Inspect properly your lower end assembly before sealing the cases • It checks the sealing of the interconnect seal OEM 45359-00 • For Twin Cam engines 00-17 890570 Interconnect seal leak testing tool Tappet Pump Up Tester • Fill completely your standard size hydraulic tappets • Inspect them physically • With the help of a drill press, check for proper feel 890568 For Twin Cam Vacuum Tappet Pump up Tool Our popular and effective bleed technology that is found in the JIMS brake bleeding tool has now been applied to hydraulic lifters. A special jar, designed for vacuum, holds up to four hydraulic lifters in a convenient tray. Once vacuum is applied, bubbles can be seen escaping from the lifters until they are completely bled. Lifters are now ready to install. No more abuse of the starting system to pump up the lifters, and no risk of damage to the valve train by running the engine, even at low RPM, when lifters have not been fully bled. A detailed manual can be found here: https://www.jimsusa.com/wp-content/ uploads/2019/10/5532-IS.pdf. Part#: 917611 , Fitment: 86-20 Sportster, 85-94 FX Model, 91-17 Dyna, 84-23 Softail, 85-23 Touring, 0923 Trike , Unit: Each , Qty.: 1 Tappet Adjustment Tool • This hand tool simplifies the way to verify proper tappet adjustment • Use on most hydraulic tappets, OEM and aftermarket • For Twin Cam, Evo, Milwaukee Eight 890567 Tappet adjustment tool Wrist Pin Bushing Reamer Tool Use with rods in or out of motor. These tools will ream your wrist pin bushings to OEM specifications, and are made to exact tolerances with pilots to locate from the I.D. of your wrist pin bushings. They are easy to use with their lead-in taper at the start of each ream. Part#: 22320 , Fitment: 36-47 Knucklehead, 48-65 Panhead, 66-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, 91-98 Dyna, 84-99 Softail, 8698 Touring , Unit: Each , Qty.: 1 Magnetic Tappet Holding Tool • The new JIMS® Magnetic Tappet Holder easily holds the tappets in the tappet bores when changing or upgrading cams • Simply install the tool over the tappet cover and the magnets will magnetically hold the tappet in place while performing any cam chest work, a time saver for any technician • Designed to work on both Twin Cam and Milwaukee-Eight engines Part#: 923736 , Fitment: 99-17 Dyna, 00-24 Softail, 99-24 Touring, 09-24 Trike , Unit: Set , Qty.: 1 Valve Guide Tool The JIMS head holder tool makes pressing valve guides in and out simple. Fitment: 05-17 Dyna, 05-17 Softail, 05-16 Touring, 09-16 Trike, 04-20 Sportster, 04-10 XB , Unit: Each , Qty.: 1 PART# DESCRIPTION 622185 7mm Assembly Pilot 622186 7mm Insert
RkJQdWJsaXNoZXIy ODQ0NDEw