Chrome plated adjusting kit, designed to fit 1936 thru 1964 transmission cases. Allows you to precisely adjust and secure the transmission. Can be used with stock or custom transmission case. Recommended when open belt-drive is installed (OEM 47720-36).
09-022 HELMETS & AUDIO PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX Speed sensor hole plug and O-ring 700822 Plug for speed sensor hole 700824 O-ring for speed sensor hole plug Fits 1986 thru 1999 Softail models 744127 Polished Fits 1986 thru 1999 Softail models 744126 Black powder coated Fits 1986 thru 1999 Softail models 744125 Plain cast aluminum These transmission cases for 1986 thru 1999 Softails are designed to be the strongest on the market with extra case thickness and full support gussets where needed. Cases are cast from A356 aluminum in CNC machined permanent molds and heat treated to T6 specifications and then fully machined on a state-of-the-art CNC horizontal machining center. Available in plain cast, polished, or black powder coated finish. Accepts electronic speed sensor. For those who do not want to use the electronic speedo sensor a plug and O-ring seal are available. Bearings, dowel pins and mounting studs are not included. 3000 HEAVY DUTY TRANSMISSION CASES 781054 Chrome 781055 Black The built in dual adjusters operate from the end of the 1/2" thick steel plate by counter bored socket head screws which allow accurate alignment of the main shaft and are ideal for open belt drive models. The three holes at the front fit various frames. Fits 4 speed Big Twin transmissions from 1979 thru 1986 with flat bottom cases and 1936 thru early 1978 cases if the sliders are milled off the bottom of the case. 2992 ADJUSTABLE TRANSMISSION PLATE FOR 4SPEED BIG TWIN 032332 Transmission adjusting kit Chrome plated adjusting kit, designed to fit 1936 thru 1964 transmission cases. Allows you to precisely adjust and secure the transmission. Can be used with stock or custom transmission case. Recommended when open belt-drive is installed (OEM 47720-36). 2991 TRANSMISSION ADJUSTING KIT HARLEY BIG TWIN 032419 Transmission adjusting kit Chrome plated "U" shape transmission adjusting kit. This transmission adjuster was designed to aid in the accurate alignment and adjustment of the transmission main-shaft parallel to the engine sprocket shaft, when an open belt-drive or tin primary is installed. Transmission is firmly held into place by four jam units. Fits all 4 Speed Big Twin transmissions 1958-1986 (except FXST). 2990 "U" SHAPE TRANSMISSION ADJUSTING KIT 231870 Fits 1937-1964 (OEM 34735-36) Chrome plated transmission adjuster screw for 4-speed and 3-speed plus reverse Big Twin transmissions 1937 thru 1964. 2989 COLONY TRANSMISSION ADJUSTER SCREW 781283 Chrome (OEM 47720-36) 781284 White plated (OEM 47720-36) 781285 Parkerized (OEM 47720-36) Exact duplicate of the transmission adjuster screw support bracket on 1936-1957 4-speed and 3-speed plus reverse Big Twin. 2988 COLONY TRANSMISSION ADJUSTER SCREW SUPPORT STRAP 781180 Parkerized (OEM 47698-36) 781179 Chrome Exact reproduction of the transmission mounting plate on 1936 thru 1957 Big Twins. 2987 4 SPEED BIG TWIN TRANSMISSION MOUNTING PLATES Knurled style, 11/16-11 thread, fits 1958 thru 1980 models (OEM 37072-79) 762628 Polished 741795 Chrome Hex style, 7/8-18 thread, fits 1936 thru 1957 models (OEM 701) 762629 Chrome 762630 White plated 762631 Parkerized Quality reproduction of the OEM transmission filler plugs, made by Colony. 2985 TRANSMISSION FILLER PLUG FOR 4 SPEED BIG TWINS 7Ȫ$Ȧ6ȥ,ȫ6ȡ2Ȧ TRANSMISSION PARTS 4 SPEED BIGTWIN (Site 652)